CREATIVE THING

       A  solenoid engine  works on the law of electromagnetic attraction. Coil magnetism attracts the plunger, and a spark distributor is used to cause the electromagnet to move as per the position of the piston without the use of sensors or microcontrollers. his magnetic field acts as an electromagnet. Solenoids  are a specially engineered electromagnet in which a coil of wire is wrapped around a specially shaped core made of steel or iron, it is an integral component in all sizes of  motors .  Solenoids  work like this: when electrical current goes through the loop of wire, a magnetic field accumulates around it. 2D Digrams CNC Machine: 1.Side support 2.Cylinder Holder 3.Bottom Support: 3D PRINTED PARTS LINK https://www.thingiverse.com/thing:4874231 Components Link : 1. Shaft (6mm) https://amzn.to/2RPjSLp 2. Ball Bearing (6mm) https://amzn.to/2RRb6wq 3. Neodymium magnet https://bit.ly/3i4OLGd 4.Shaft (3mm) https://amzn.to/2R8k...

     BLDC motor  works on the  principle  similar to that of a conventional DC  motor , the Lorentz force law which states that whenever a current carrying conductor placed in a magnetic field it experiences a force. As a consequence of reaction force, the magnet will experience an equal and opposite force.      A brushed DC  motor  has permanent magnets on the inside of its structure, with a spinning armature on the inside. In  brushless DC motors , the permanent magnets are on the rotor, and the electromagnets are on the stator. A computer then charges the electromagnets in the stator to rotate the rotor a full 360-degrees. CONNECTIONS Components: 1. Copper wire 2. Ball bearing (5mm) - 2pcs 3. Shaft (5mm× 75mm) -1pcs 4. Neodymium magnets - 4pcs YOUTUBE VIDEO LINK: 3D PRINTER PART 'stl' FILE https://www.thingiverse.com/thing:4866578 Components Link :   1. Bearing (5mm) https://amzn.to/3v9KLrW...

I am making v6 model using 12 dc mini motor arrangement using gears. My Model Diagram: how to make above project. Youtube video link avabile in below. The V6 engine consists of a crankshaft onto which the six cylinders are attached in two arrays. Each of the arrays has three cylinders, set at a right angle (90°), an acute angle (60°), or an obtuse (120°). ... Since the banks have an odd number of cylinders, the V6 engine is not balanced naturally. Orginal V6 Diagram: Components list: 1. Dc motor -6pcs 2. Ball bearing (5mm) - 4pcs 3. Ball bearing (8mm) - 2pcs 4. Shaft (8mm×130mm) -1pcs 5. Shaft (5mm× 35mm) -2pcs 6. Bevel Gear (42mm) -3pcs 7. Bevel gear (22mm) - 6pcs 8. Computer Ventilization fan - 2pcs 9. Ply wood 10. Fan body - 1pcs 11. Helical gear (70mm) - 1pcs 12. Helical gear (36mm) - 2pcs 13. Wires Youtube Video link https://youtu.be/mMTfM8OQwyc 3D PRINTER LINK: https://www.thingiverse.com/thing:4866567 COMPONENTS LINK: 1.DC Motor https://amzn.to/2SZXRcW 2. Shaft (8mm) htt...

  All jet engines, which are also called gas turbines, work on the same principle. The engine sucks air in at the front with a fan. ... The burning gases expand and blast out through the nozzle, at the back of the engine. As the jets of gas shoot backward, the engine and the aircraft are thrust forward. I am using on this project Three brushed dc motor (12V). This motor connect on single shaft with help of bevel gear. Bevel gear, motor holder and all parts available in "stl" file. Components list: 1. Dc motor -3pcs 2. Ball bearing (5mm) - 4pcs 3. Ball bearing (8mm) - 2pcs 4. Shaft (8mm×70mm) -1pcs 5. Shaft (5mm× 35mm) -2pcs 6. Bevel Gear (42mm) -1pcs 7. Bevel gear (22mm) - 3pcs 8. Computer Ventilization fan - 2pcs 9. Motor holding body - 1 pcs 10. Fan body - 1pcs 11. Helical gear (70mm) - 1pcs 12. Helical gear (36mm) - 2pcs 13. Screws -6pcs Youtube Video link 3D PRINTER LINK: https://www.thingiverse.com/thing:4866558 COMPONENTS LINK: 1.DC Motor https://amzn.to/2SZXRcW 2. Shaf...

The  principles  of  CNC operation . Movement of X, Y, Z axis are controlled by a motor which supplies either Alternating current or Direct current. Movement of the  machine  is done by giving commands. All the operations are carried out by codes like speed, feed, depth of cut, etc   working Area= 600mm x 400mm Circuit Diagram: 3d printed Files https://www.thingiverse.com/thing:4862973/files youtube Video link https://youtu.be/Hb6WJTX5X_E Detail, 1.16mm shaft 400mm=2pcs 600mm=4pcs 2. linear bearing (16mm)=12pcs 3.12mm shaft(200mm=2pcs) 4.linear bearing (12mm)=4pcs 5.nema 23 stepper motor= 4pcs 6. 8mm to 10mm shaft coupler=4pcs 7. Lead Screw 400mm =1PCS 600mm =2pcs 200mm =1pcs 8.palm router=1 9.2040 Aluminum Profile(400mm)=2pcs 10. 2080 Aluminum Profile(600mm)=2pcs 200mm=1pcs 11. Lead screw nut (10mm)=4pcs 12. bearing (10mm)=4pcs link: Components Link : 1. 2040 Aluminum Profile https://amzn.to/3ubzIh0 2. 2080 Aluminum Profile https://bit.ly/2Rax50u 3...

Description : I am show about free energy generator using neodymium magnetic field. the magnets create a magnetic field, the copper coil absorb from magnetic field and convert the energy. Components Needed: 1. Copper Coil : i). The copper coil are winding on pvc pipe. ii). The pvc pipe dia are (20mm, 32mm) 2. DC Motor i). The dc motor are mainly used electric energy into mechanical energy. ii). the kit are used on 3V motor 3. neodymium magnet i). The magnets are high power energy generated. 4. Water Can Cap 5.Wood i). The plywood turning at 40mm diameter. ii). The water can cap are fixed in 60 Degree each. 6. Bolt and Nut i). The bolt and nut used for core. Procedure: i). The magnets placed at water can cap. ii). All caps are placed in wood . iii).The turbine are fixed in dc motor. iv). The coil and core placed in rectangular wooden piece. "THIS KIT  ARE WORKING IN 40SEC ONLY". This Video Link: Social M...